ISO 9001:2015 certifiedIAPMO SCBCert. 1117610

Contact sales@calpexplastics.com (760) 254-9162

Industries · Water filtration & irrigationISO 9001:2015 · Since 1980

Extrusions for water filtration and irrigation.

Calpex Plastics is an extruded plastic tubing supplier to the agriculture and irrigation equipment industry: we make nylon and polyethylene irrigation tubing to your print, from 1/16 to 3 in outside diameter.

Water filtration and irrigation are among the industries we serve, with agriculture and farming, plumbing, and turf and garden. Tubing, pipe and profiles are extruded in our Oceanside, California plant.

Applications

Where our water and irrigation extrusions are used.

Irrigation tubing, drip-irrigation and sprinkler pipe, acrylic tubing and fluid-management tubing, each made to your drawing.

  • Irrigation tubing

    Nylon tubing is heat and crack resistant and handles pneumatic applications. It is widely used for irrigation tubing and refrigerator water lines.

  • Drip irrigation and sprinkler pipe

    LDPE pipe suits drip irrigation systems, sprinklers and drainage; HDPE pipe offers good temperature resistance for drainage systems. Pipe runs from 1/8 to 3 in.

  • Water lines

    Tubing for water lines, in polyethylene, vinyl, nylon or polyurethane, cut to length, with plain or belled ends where the joint needs them.

  • Acrylic tubing

    Acrylic tubing ranges from opaque to nearly transparent, for applications where you need to see the liquid inside and keep an eye on its condition.

  • Agricultural equipment

    Urethane suits agricultural applications that need abrasion resistance, flexibility and impact resistance. Agriculture is a published industry for our polyurethane dual-lumen tubing.

  • Fluid management

    Tubing can be tailored for load, flexibility, strength and corrosion resistance, and to stand up to hazardous, toxic or acidic contents.

Recommended materials

Resins for water and irrigation parts.

The resin families we extrude for water filtration and irrigation, what we make from each and why it is used.

Typical properties of each resin family, as published on our product pages. The grade for your part is set by your drawing and application.
MaterialWe extrude it asWhy it is used, as published
NylonTubingHeat and crack resistant; widely used for irrigation tubing and refrigerator water lines.
LDPEPipe, tubingFlexible; suits drip irrigation systems, sprinklers and pneumatic lines.
HDPEPipe, tubingGood temperature resistance for drainage systems; sturdy for high-impact uses.
AcrylicTubingOpaque to nearly transparent, so the liquid inside can be observed.
Flexible vinylTubingVersatile for commercial, consumer and industrial uses; does not corrode.
PolyurethaneTubing (incl. dual-lumen)Abrasion resistance, flexibility and impact resistance; used in agricultural applications.

All materials we extrude

Capabilities

Made, finished and tooled in one plant.

  • Striping

    A co-extruded stripe on tubing or rods, added at the die, to mark or identify your part.

  • Printing

    Markings printed along tubing and other extruded parts, so each length can be identified after it ships.

  • Cutting and tape application

    Parts cut to length, and tape applied, after extrusion.

  • Tube belling

    Belled ends on tubing and pipe. Pipe can also have plain or chamfered ends.

Do you supply tubing to the agriculture and irrigation equipment industry?

Yes. We extrude nylon irrigation tubing and polyethylene tubing to your print, and LDPE pipe for drip irrigation systems and sprinklers. Agriculture and farming is on our published list of industries served.

Can you supply food-contact compliant tubing?

Food-contact compliant resins available, with documentation supplied on request.

What tubing sizes do you make?

Tubing from 1/16 to 3 in outside diameter, made to your print. Wall thickness follows your drawing and depends on the material and geometry. Pipe runs from 1/8 to 3 in.

Can tubing be striped or printed?

Yes. A co-extruded stripe can be added at the die, and tubing can be printed, to mark or identify it.

What quantities and lead times can you handle?

Tell us the quantity you need, and we will quote it; blanket orders are available. Each project is quoted with its own lead time, typically 4–6 weeks with shipping.

Request a quote

Send the print. We’ll quote the part.

Attach your drawing here, or email sales@calpexplastics.com. Short runs to high volume; blanket orders available.

Attach a drawing. Blanket orders available.

What happens next
  1. 01We confirm receipt by email.
  2. 02Our engineers review your drawing and contact you with design questions.
  3. 03You receive a quote. Lead times are quoted per project.

See our plant: the factory tour, 2:58

NDA on request

Name
File

Drop drawings here or , up to 50 MB each. Accepted files: STEP, STP, IGES, IGS, DWG, DXF, STL, IronCAD, SolidWorks, PDF, ZIP, JPG or PNG.: STEP, IGES, DWG, DXF, STL, IronCAD, SolidWorks, PDF, ZIP, JPG, PNG · 50 MB each

Quantity, material or anything else we should know.

ISO 9001:2015 · Since 1980 · Made in Oceanside, CA

Files go only to Calpex sales and engineering. See our Privacy policy.